IP profile

[#1]

This is my router info as requested by mod
Modem Status Connected
DownStream Connection Speed 3971 Kbps
UpStream Connection Speed 448 Kbps
VPI 0
VCI 38
and this was my speed results :-
1. Best Effort Test:  -provides background information.

Download  Speed
3.34 Mbps
 
0 Mbps 4 Mbps
Max Achievable Speed

Download speedachieved during the test was - 3.34 Mbps
For your connection, the acceptable range of speeds is 1.2 Mbps-4 Mbps.
IP Profile for your line is - 3.5 Mbps
2. Upstream Test:  -provides background information.

Upload Speed
0.35 Mbps
 
0 Mbps 0.45 Mbps
Max Achievable Speed

Upload speed achieved during the test was - 0.35Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.45 Mbps

Can this be upped any more, every little helps
Paul

[#2]

Can this be improved?
That would depend on other router metrics which you have not disclosed.  Knowledge of the US and DS attenuation and SNRM will allow an assessment of the viability of squeezing more synch speed out of the line.
Your data transfer rate looks good for the synch speed.

[#3]

ADSL Link Downstream Upstream
Link Rate 3971 Kbps 448 Kbps
Line Attenuation 56.0 dB 34.1 dB
Noise Margin 3.2 dB 10.7 dB
Is this the info

[#4]

Hi again Paul,
getting closer 
When you log in to the Modem/Router you find yourself at the Home page. Select Broadband Connection on the LHS.Then select DSL Connection below that or alternatively View more...... in the middle. Then on the RHS click Details and you should then see something like -
Link Information

Uptime: 0 days, 1:18:25
DSL Type: ITU-T G.992.1
Bandwidth (Up/Down) [kbps/kbps]: 448 / 7,456
Data Transferred (Sent/Received) [MB/MB]: 2.18 / 1.74
Output Power (Up/Down) [dBm]: 12.5 / 19.8
Line Attenuation (Up/Down) [dB]: 21.5 / 39.0
SN Margin (Up/Down) [dB]: 9.0 / 6.2
System Vendor ID (Local/Remote): TMMB / ----
Chipset Vendor ID (Local/Remote): BDCM / TSTC
Loss of Framing (Local/Remote): 0 / -
Loss of Signal (Local/Remote): 0 / -
Loss of Power (Local/Remote): 0 / -
Loss of Link (Remote): -
Error Seconds (Local/Remote): 2 / -
FEC Errors (Up/Down): 9 / 1,676
CRC Errors (Up/Down): 0 / 2
HEC Errors (Up/Down): - / 12
Just do a copy and paste of yours and post it.
HTH.

[#5]

Nah you got me lol, looked everywhere for this info and cannot find it the router is a Netgear DGN2200v3. I have clicked on all the setting tabs and cannot find any thing that looks similar to what you have posted :9

[#6]

Ah, now there was me thinking you had a tg582n, that explains it, sorry you won't get that lot. What you've posted will have to do, it would have been nice to see some error figures, I'm not sure where they are on that one, if they are shown, if you know post them.

[#7]

Just had a quick look at the manual, if you are running standard firmware, it doesn't give them. So ..
As far as the stats above go your line is doing a touch better than some would. But tell use a bit about you installation and we'll see if there's anything that might improve it.
Do you have a Master Socket like the one on the left?
It has the join across it half way down.
Do you have any extension phone sockets, and where are you currently plugged in? Are you using any plug-in phone/router extension leads?
I presume you can't hear/have heard any crackling or other noises on the line when using the phone nor have you had any problems with incoming or outgoing calls?

[#8]

Open reach fitted a new style fibre socket when they found the issue with the line which was external to the house (noise on the line) they have now wired so no external filters are needed at any ext point.
No noise on line
Paul

[#9]

Ah ok that's good, so you are plugged into the top socket on that then? And do you have any fixed extensions at all?

[#10]

Yes router plugged into top socket only ext is a phone downstairs and the alarm panel these no longer have micro filters attached
Kind regards
Paul

[#11]

Ok then I don't think there's an awful lot more to suggest.  I would have suggested looking at bell wires, but if you have an alarm system, I'm reluctant to suggest you tamper. See how it goes, with your external problem sorted let's hope your connection is stable.

[#12]

I believe the vdsl2 interstertial plate filters the bell wire so that it doesn't back feed onto the unfiltered data socket.

[#13]

I have already removed pin 3 (bell wire) from all the sockets

[#14]

Ah, good. OK Did you remove it at the master? Which you can do at some convenient point if you didn't.
@njay
That is actually irrelevant, the filtering isn't always 100% effective. It's a similar situation with the older BT SSFP and some other Filtered Front plates and often removal of the bell wire will give further improvement.

[#15]

so it looks like im getting the best possible ip profile?