Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
PAP2 hardware setup
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Plusnet Community
- :
- Forum
- :
- Other forums
- :
- Tech Help - Software/Hardware etc
- :
- PAP2 hardware setup
PAP2 hardware setup
08-12-2007 12:11 PM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
I have a Linksys PAP2-NA adapter which works fine on outgoing pstn calls, but I'm getting one way transmission on incoming calls.
Any ideas?
Any ideas?
5 REPLIES 5
Re: PAP2 hardware setup
08-12-2007 7:38 PM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Line One Info Basic setup
Line Enable: yes
sip port :5060
proxy :sip2.plus.net Register: Yes
Make Call Without Reg: No Register Expires: 3600
Ans Call Without Reg : No
Display Name: sip id number User ID: sip id number
Password: sip password Use Auth ID: Yes
Auth ID: sip id number
Audio Configuration
Preferred Codec:G7LLu Silence Supp Enable: no
Use Pref Codec Only:No FAX CED Detect Enable:No
DTMF Tx Method: INFO
Line Enable: yes
sip port :5060
proxy :sip2.plus.net Register: Yes
Make Call Without Reg: No Register Expires: 3600
Ans Call Without Reg : No
Display Name: sip id number User ID: sip id number
Password: sip password Use Auth ID: Yes
Auth ID: sip id number
Audio Configuration
Preferred Codec:G7LLu Silence Supp Enable: no
Use Pref Codec Only:No FAX CED Detect Enable:No
DTMF Tx Method: INFO
Re: PAP2 hardware setup
09-12-2007 7:10 PM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Thanks Puddy
I've checked and all the settings were as you said except the fax ced dectect. I changed that but still the same. I understand that lots of people are experincing one way transmission on i/c calls when using the soft phone as well.
I've checked and all the settings were as you said except the fax ced dectect. I changed that but still the same. I understand that lots of people are experincing one way transmission on i/c calls when using the soft phone as well.
Re: PAP2 hardware setup
10-12-2007 5:02 AM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Quote from: DickB Thanks Puddy
I've checked and all the settings were as you said except the fax ced dectect. I changed that but still the same. I understand that lots of people are experincing one way transmission on i/c calls when using the soft phone as well.
Try this one
Proxy and Registration
Outbound Proxy:nat.plus.net:5082
save settings
puddy
Re: PAP2 hardware setup
10-12-2007 8:56 AM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
DickB
you might also need to forward UDP ports 5060 to 5061 and 16384 to 16482 through your router to the IP address used by the PAP2. You will need to set the PAP2 to use a static IP address for this to work reliably. I've got a linksys SPA2002 which is similar to a PAP2 and this worked for me. See http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=5204&lid=7925542973B...
Regards, Mike
you might also need to forward UDP ports 5060 to 5061 and 16384 to 16482 through your router to the IP address used by the PAP2. You will need to set the PAP2 to use a static IP address for this to work reliably. I've got a linksys SPA2002 which is similar to a PAP2 and this worked for me. See http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=5204&lid=7925542973B...
Regards, Mike
Re: PAP2 hardware setup
10-12-2007 11:24 PM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page