Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
Request for ADSL2+ with capped upstream
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Plusnet Community
- :
- Forum
- :
- Help with my Plusnet services
- :
- Broadband
- :
- Request for ADSL2+ with capped upstream
Request for ADSL2+ with capped upstream
30-05-2013 9:53 AM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
I would like my line to be set for ADSL2+ with capped upstream. I think that would be better than its current strange ADSL1 with uncapped upstream mode.
Current line stats:
"Trained mode: 3" indicates G.dmt aka ADSL1. I think the target SNRM is 9 mainly for historical reasons, the line used to run much slower until I disconnected the bell wires about 3 years ago. And the only time the SNRM was reduced from 12 to 9 was after the line was accidentally running on ADSL2+ a while ago.
I also have a wildly optimistic estimate of 4.5Mbps from BTWholesale, which is estimating ADSL2+ will be 50% faster!
Current line stats:
[DSL Modem Stats]
US Connection Rate: 640 DS Connection Rate: 2752
DS Line Attenuation: 57.5 DS Margin: 9.0
US Line Attenuation: 31.5 US Margin: 11.0
US Payload : 212293344 DS Payload: 3013981056
US Superframe Cnt : 12845126 DS Superframe Cnt: 12845127
US Transmit Power : 0 DS Transmit Power: 0
LOS errors: 0 SEF errors: 0
Errored Seconds: 0 Severely Err Secs: 0
Frame mode: 3 Max Frame mode: 0
Trained Path: 1 US Peak Cell Rate: 1509
Trained Mode: 3 Selected Mode: 1
ATUC Vendor Code: 54535443 ATUC Revision: 3
Hybrid Selected: 3 Trellis: 1
Showtime Count: 7 DS Max Attainable Bit Rate: 2752 kbps
BitSwap: 1 US Max Attainable Bit Rate: n/a
Annex: AnxA psd_mask_qualifier: 0x0000
Power Management Status: L0 DS HLINSC: 0
US ACTPSD: -345 DS ACTPSD: -355
Total init. errors: 0 Total init. timeouts: 0
Showtime init. errors: 0 Showtime init. timeouts: 0
Last showtime init. errors: 0 Last showtime init. timeouts: 0
ATUC ghsVid: b5 00 54 53 54 43 05 10
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
ATUR ghsVid: b5 00 54 53 54 43 00 00
T1413Vid: 00 00 T1413Rev: 00 VendorRev: 00
[Upstream (TX) Interleave path]
CRC: 11 FEC: 1088 NCD: 0
LCD: 0 HEC: 272
[Downstream (RX) Interleave path]
CRC: 1271 FEC: 41209 NCD: 0
LCD: 0 HEC: 0
"Trained mode: 3" indicates G.dmt aka ADSL1. I think the target SNRM is 9 mainly for historical reasons, the line used to run much slower until I disconnected the bell wires about 3 years ago. And the only time the SNRM was reduced from 12 to 9 was after the line was accidentally running on ADSL2+ a while ago.
I also have a wildly optimistic estimate of 4.5Mbps from BTWholesale, which is estimating ADSL2+ will be 50% faster!
Message 1 of 2
(492 Views)
1 REPLY 1
Re: Request for ADSL2+ with capped upstream
30-05-2013 1:02 PM
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Highlight
- Report to Moderator
Message 2 of 2
(274 Views)
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Plusnet Community
- :
- Forum
- :
- Help with my Plusnet services
- :
- Broadband
- :
- Request for ADSL2+ with capped upstream